National Instruments NI 6232 User Manual Page 152
- Page / 180
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
© National Instruments Corporation G-1 NI 6232/6233 User Manual
Glossary
Numbers/Symbols
% Percent.
+ Positive of, or plus.
– Negative of, or minus.
± Plus or minus.
< Less than.
> Greater than.
Less than or equal to.
Greater than or equal to.
/Per.
º Degree.
Ω Ohm.
A
A Amperes—the unit of electric current.
A/D Analog-to-Digital. Most often used as A/D converter.
AC Alternating current.
accuracy A measure of the capability of an instrument or sensor to faithfully indicate
the value of the measured signal. This term is not related to resolution;
however, the accuracy level can never be better than the resolution of the
instrument.
ADE Application development environment.
- DAQ M Series 1
- Important Information 3
- Compliance 5
- Chapter 3 7
- Chapter 4 7
- Chapter 5 8
- Chapter 6 9
- Chapter 7 9
- Contents 10
- About This Manual 13
- Related Documentation 14
- NI-DAQmx Base 15
- LabWindows 16
- Measurement Studio 16
- Training Courses 17
- Technical Support on the Web 17
- Getting Started 18
- Device Specifications 19
- Device Accessories and Cables 19
- DAQ System Overview 20
- DAQ-STC2 21
- Sensors and Transducers 22
- Cables and Accessories 23
- Chapter 2 DAQ System Overview 24
- Connector Information 25
- Analog Input 28
- Analog Input Range 29
- (10 V – (–10 V)) 30
- = 305 mV 30
- Figure 4-2. PGIA 31
- Software 32
- Use Low Impedance Sources 33
- Chapter 4 Analog Input 34
- Example 1 36
- Example 2 36
- Software-Timed Acquisitions 36
- Hardware-Timed Acquisitions 37
- Buffered 37
- Analog Input Triggering 38
- Types of Signal Sources 39
- Floating Signal Sources 40
- Differential Input Biasing 42
- Signal Sources 44
- Field Wiring Considerations 45
- Analog Input Timing Signals 46
- Sample Counter 48
- AI Sample Clock Signal 49
- Using an Internal Source 50
- Using an External Source 50
- Terminal 50
- Other Timing Requirements 50
- AI Convert Clock Signal 52
- AI Hold Complete Event Signal 55
- AI Start Trigger Signal 55
- Using a Digital Source 55
- AI Reference Trigger Signal 56
- AI Pause Trigger Signal 57
- Software-Timed Generations 60
- Hardware-Timed Generations 61
- Non-Buffered 61
- Analog Output Triggering 62
- Analog Output Timing Signals 63
- AO Start Trigger Signal 64
- AO Pause Trigger Signal 65
- AO Sample Clock Signal 66
- Chapter 5 Analog Output 68
- Digital Input and Output 70
- Logic Conventions 72
- Terminals section 75
- Counter Input Applications 76
- Pulse-Width Measurement 79
- Period Measurement 80
- Single Period Measurement 81
- Buffered Period Measurement 81
- Semi-Period Measurement 82
- Frequency Measurement 83
- Counter (Averaged) 84
- Using Two Counters 86
- Figure 7-14. Method 3 87
- Position Measurement 89
- X2 Encoding 90
- X4 Encoding 90
- Channel Z Behavior 90
- 890 21743 91
- Counter Output Applications 94
- Pulse Train Generation 96
- Frequency Generation 97
- Using the Frequency Generator 97
- Frequency Division 98
- Pulse Generation for ETS 98
- Counter Timing Signals 99
- Counter n Source Signal 100
- Counter n Gate Signal 101
- Counter n Aux Signal 101
- Counter n Up_Down Signal 102
- Counter n HW Arm Signal 103
- Default Counter Terminals 104
- Counter Triggering 105
- Other Counter Features 106
- Prescaling 107
- Duplicate Count Prevention 108
- Duplicate Count Example 109
- Chapter 7 Counters 110
- Synchronization Modes 111
- 80 MHz Source Mode 112
- Other Internal Source Mode 113
- External Source Mode 113
- Chapter 8 PFI 115
- Connecting PFI Input Signals 116
- PFI Filters 117
- I/O Protection 118
- Programmable Power-Up States 119
- Table 9-1. Ground Symbols 122
- Digital Isolation 123
- Digital Routing and Clock 124
- Generation 124
- 80 MHz Timebase 125
- 20 MHz Timebase 125
- 100 kHz Timebase 125
- External Reference Clock 125
- 10 MHz Reference Clock 126
- RTSI Connector Pinout 127
- Using RTSI as Outputs 128
- RTSI Filters 129
- Figure 10-3. Filter Example 130
- Table 10-2. Filters 130
- PXI Clock and Trigger Signals 131
- PXI_STAR Filters 132
- Figure 10-4. Filter Example 133
- Bus Interface 134
- PXI Considerations 135
- Data Transfer Methods 136
- Interrupt Request (IRQ) 137
- Programmed I/O 137
- Triggering 138
- • Analog output generation 139
- • Counter behavior 139
- Device-Specific Information 140
- Figure A-1. NI 6232 Pinout 141
- NI 6232 Specifications 142
- Screw Terminal 142
- NI 6233 Pinout 143
- Figure A-2. NI 6233 Pinout 144
- NI 6233 Specifications 145
- Troubleshooting 147
- Channel 0 148
- Channel 1 148
- Convert Period 148
- Sample Period 148
- Analog Output 149
- Counters 149
- Technical Support and 150
- Professional Services 150
- Glossary 152
- Numerics 171
Related products and manuals for Measuring, testing & control National Instruments NI 6232
(48 pages)© 2020, manymanuals.com. All rights reserved. | 2.888 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals