National Instruments AT User Manual Page 22
- Page / 208
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 1 Introduction
Serial Hardware and Software for Windows 1-8 ni.com
NI-Serial Software Overview
The NI-Serial software for Windows 2000/NT/Me/9x includes a native
Windows 2000/Me/9x device driver and Windows NT kernel driver that
provide full interrupt-driven, buffered I/O for multiple COM ports. You
can obtain a maximum baud rate of either 460.8 KBaud (PCI/PXI-485 kits)
or 115.2 KBaud (PCI/PXI/PCMCIA/AT-232 kits). You can also use up to
256 serial ports under Windows 2000 or up to 99 serial ports under
Windows NT/Me/9x. The NI-Serial software also includes a configuration
utility, which is fully integrated into the Windows 2000/Me/9x Device
Manager and Windows NT Control Panel. For more information about
software specifications, refer to Appendix E, Specifications.
The NI-Serial software includes the following components:
• Device driver
• Diagnostic utility
• Configuration utility
• Product manuals
Time-Saving Development Tools
Your kit includes the NI-Serial software for Windows 2000/NT/Me/9x.In
addition, you can order the Measurement Studio or LabVIEW software
from National Instruments to speed your application development time and
make it easier to communicate with your instruments.
LabVIEW is an easy-to-use, graphical programming environment you can
use to acquire data from thousands of different instruments, including
IEEE 488.2 devices, VXI devices, serial devices, PLCs, and plug-in data
acquisition boards. After you have acquired raw data, you can convert it
into meaningful results using the powerful data analysis routines in
LabVIEW. LabVIEW also comes with hundreds of instrument drivers,
which dramatically reduce software development time, because you do not
have to spend time programming the low-level control of each instrument.
- Serial Hardware and 1
- Software for Windows 1
- User Manual 1
- Important Information 3
- Compliance 4
- Chapter 4 7
- Chapter 3 7
- Contents 10
- About This Manual 12
- Related Documentation 13
- FIFOs, National Semiconductor 14
- EXAR Corporation 14
- Introduction 15
- What You Need to Get Started 16
- Optional Equipment 17
- Serial Hardware Overview 17
- PXI Kits 18
- Chapter 1 Introduction 19
- PCMCIA Kits 20
- NI-Serial Software Overview 22
- Time-Saving Development Tools 22
- Figure 2-3 30
- Advanced Settings 31
- Figure 2-6 36
- Transceiver Mode 54
- Use FIFO Buffers 54
- FIFO Buffer Size 68
- Configuration 69
- Figure 4-6 79
- FIFO Enabled 89
- FIFO Buffers 89
- PCMCIA-232/2, PCMCIA-485/2 91
- Windows Me/9x 100
- Install the Hardware 101
- Figure 5-5 102
- AT Serial Board Installation 102
- Verify the Installation 103
- Verify the Hardware Resources 104
- Run the Diagnostic Test 105
- Port Settings Tab 107
- Advanced Port Settings 108
- Windows NT 109
- Install the Serial Hardware 110
- General Port Settings 114
- Resources 115
- Resource Settings 115
- AT Boards (Shared IRQ) 116
- AT Boards (Non-Shared IRQ) 117
- Using Your Serial Hardware 118
- Four-Wire Mode 119
- Two-Wire Mode: DTR with Echo 119
- Two-Wire Mode: DTR Controlled 119
- Windows 2000 120
- Windows NT/Me/9x 122
- Connector Descriptions 123
- DB-9 Connector 124
- Modular Jack Connector 125
- DB-25 Connector 126
- PCI serial board 127
- 68-Pin Connector 128
- Table A-4 129
- 100-Pin Connector 130
- Table A-5 131
- Serial Port Information 132
- Serial Communication Issues 134
- Half Duplex 135
- Termination 136
- Bias Resistors 136
- DTE vs. DCE 138
- Uninstalling the 139
- Hardware and Software 139
- PCI Hardware 140
- Uninstall the Software 141
- Uninstall the Hardware 141
- PXI Hardware 145
- PCMCIA Hardware 150
- AT Hardware 155
- Figure C-11 157
- Troubleshooting and 160
- Common Questions 160
- Address Test Failed 162
- Interrupt Test Failed 162
- PCI and PXI Boards 166
- AT Boards 166
- PCMCIA Boards 167
- \Windows\system 168
- PCI and PXI Hardware 170
- AT and PCMCIA Hardware 172
- Resolving Resource Conflicts 178
- WinNT\system32\drivers 179
- Specifications 183
- Four-Port Boards 184
- Isolated Four-Port Boards 184
- Eight-Port Boards 185
- 16-Port Boards 185
- Environmental Characteristics 186
- Software Characteristics 186
- PXI Serial Hardware 187
- PCMCIA Serial Hardware 190
- AT Serial Hardware 191
- Technical Support Resources 194
- Worldwide Support 195
- Glossary 197
- Numerics 199
Related products and manuals for Chassis components National Instruments AT
(101 pages)© 2020, manymanuals.com. All rights reserved. | 1.547 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals