National Instruments AT User Manual Page 69
- Page / 208
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
© National Instruments Corporation 4-1 Serial Hardware and Software for Windows
4
PCMCIA Serial Hardware
Installation, Verification, and
Configuration
This chapter describes how to install the NI-Serial software and PCMCIA
serial hardware and how to verify the installation. It also describes how to
view or change the communication port settings.
To begin your installation, see the section of this chapter containing
instructions for your operating system (Windows 2000, Windows Me/9x,or
Windows NT.)
Windows 2000
Install the Software
Before you install your serial hardware, complete the following steps to
install the NI-Serial software for Windows 2000:
1. Select Start»Settings»Control Panel.
2. Double-click on the Add/Remove Programs icon. The Add/Remove
Programs dialog box appears.
3. ClickontheAdd New Programs button and then the CD or Floppy
button.
4. When prompted, insert the NI-Serial Software for Windows
2000/NT/Me/9x CD and click on the Next button.
5. When prompted, click on the Finish button to install the program files
from the CD.
6. The setup wizard begins. The setup wizard guides you through the
necessary steps to install the NI-Serial software. To exit the setup
wizard at any time, click on the Cancel button.
7. If you need to install your hardware, or if this is your first time to install
the NI-Serial software for Windows 2000, skip to the next section,
Install the Hardware. Otherwise, continue to step 8.
- Serial Hardware and 1
- Software for Windows 1
- User Manual 1
- Important Information 3
- Compliance 4
- Chapter 4 7
- Chapter 3 7
- Contents 10
- About This Manual 12
- Related Documentation 13
- FIFOs, National Semiconductor 14
- EXAR Corporation 14
- Introduction 15
- What You Need to Get Started 16
- Optional Equipment 17
- Serial Hardware Overview 17
- PXI Kits 18
- Chapter 1 Introduction 19
- PCMCIA Kits 20
- NI-Serial Software Overview 22
- Time-Saving Development Tools 22
- Figure 2-3 30
- Advanced Settings 31
- Figure 2-6 36
- Transceiver Mode 54
- Use FIFO Buffers 54
- FIFO Buffer Size 68
- Configuration 69
- Figure 4-6 79
- FIFO Enabled 89
- FIFO Buffers 89
- PCMCIA-232/2, PCMCIA-485/2 91
- Windows Me/9x 100
- Install the Hardware 101
- Figure 5-5 102
- AT Serial Board Installation 102
- Verify the Installation 103
- Verify the Hardware Resources 104
- Run the Diagnostic Test 105
- Port Settings Tab 107
- Advanced Port Settings 108
- Windows NT 109
- Install the Serial Hardware 110
- General Port Settings 114
- Resources 115
- Resource Settings 115
- AT Boards (Shared IRQ) 116
- AT Boards (Non-Shared IRQ) 117
- Using Your Serial Hardware 118
- Four-Wire Mode 119
- Two-Wire Mode: DTR with Echo 119
- Two-Wire Mode: DTR Controlled 119
- Windows 2000 120
- Windows NT/Me/9x 122
- Connector Descriptions 123
- DB-9 Connector 124
- Modular Jack Connector 125
- DB-25 Connector 126
- PCI serial board 127
- 68-Pin Connector 128
- Table A-4 129
- 100-Pin Connector 130
- Table A-5 131
- Serial Port Information 132
- Serial Communication Issues 134
- Half Duplex 135
- Termination 136
- Bias Resistors 136
- DTE vs. DCE 138
- Uninstalling the 139
- Hardware and Software 139
- PCI Hardware 140
- Uninstall the Software 141
- Uninstall the Hardware 141
- PXI Hardware 145
- PCMCIA Hardware 150
- AT Hardware 155
- Figure C-11 157
- Troubleshooting and 160
- Common Questions 160
- Address Test Failed 162
- Interrupt Test Failed 162
- PCI and PXI Boards 166
- AT Boards 166
- PCMCIA Boards 167
- \Windows\system 168
- PCI and PXI Hardware 170
- AT and PCMCIA Hardware 172
- Resolving Resource Conflicts 178
- WinNT\system32\drivers 179
- Specifications 183
- Four-Port Boards 184
- Isolated Four-Port Boards 184
- Eight-Port Boards 185
- 16-Port Boards 185
- Environmental Characteristics 186
- Software Characteristics 186
- PXI Serial Hardware 187
- PCMCIA Serial Hardware 190
- AT Serial Hardware 191
- Technical Support Resources 194
- Worldwide Support 195
- Glossary 197
- Numerics 199
Related products and manuals for Chassis components National Instruments AT
(101 pages)© 2020, manymanuals.com. All rights reserved. | 0.161 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals